Where Are Brake Light Located 2015 Kia Optima
Kia Optima Tail Light Bulbs Replacement Guide
How to change a burnt out brake, turn signal or reverse bulb in the tail lights of a 3rd generation 2011 to 2015 Kia Optima.
2013 Optima Tail Light
Open Trunk Lid
Access Cover In Liner
Owners of other Kia and Hyundai vehicles with similar tail light assemblies such as the Forte, Cadenza, Rio, Soul, Sedona, Sorento, Sportage, Sonata, Accent, Elantra, Veloster, Azera, Tucson, Santa Fe and Genesis may also find these DIY instructions to be helpful.
Replacement bulbs with their part numbers are as follows: Brake # 1157, Turn Signal # 1156 or 2357A, Side Marker # 168, Parking Light # 1156 or 2357A and Reverse # 921.
The bulbs vary depending on the model year.
Please check your OEM (original) bulbs or the Amazon Part Finder website.
No tools are needed to change a standard incandescent brake, rear turn signal or side marker bulb.
To replace the parking light and reverse bulbs inside the inner tail light housing, you'll need a Phillips head screwdriver, a 10mm socket and a 1/4" drive ratchet.
Pull Off Access Door
White Plastic Connector
Pull Off Connector
This 2013 Optima LX has all standard incandescent tail light bulbs except for the LED third brake light.
The outer tail light housings on each rear corner of the vehicle contain the brake, rear turn signal and rear side marker bulbs.
Move to the inside corner of the trunk and pull off the rectangular access cover on the carpeted liner.
Pull the white plastic power connector off its mounting peg and move it out of the way.
Move Plug Away
1/4 Turn Counter Clockwise
Pull Out Brake Light Socket
Pull the brake light socket straight out of the housing.
Push Down & 1/4 Turn CC
Replace 1/4 Turn Clockwise
Turn Signal Bulb Socket
Push a new # 1157 dual filament brake light bulb down in to the socket and rotate it 1/4 turn clockwise to secure it in place.
1/4 Turn Counter Clockwise
Push Down & 1/4 Turn CC
Re-Install 1/4 Turn Clockwise
Rotate the socket 1/4 turn counter clockwise and pull it straight out of the housing.
Push the old bulb down in to the socket and rotate it 1/4 turn counter clockwise before pulling it straight out.
Push a new clear # 1156 bulb or amber colored # 2357A bulb (depending on your car's model year and trim level) down in to the socket and rotate it 1/4 turn clockwise to secure it in place.
Re-insert the bulb socket in to the housing and rotate it 1/4 turn clockwise to secure it in place.
Side Marker Bulb Socket
1/4 Turn Counter Clockwise
Old # 168 Side Marker Bulb
Pull the old bulb straight out of the socket and push in a new # 168 bulb.
If necessary, you may also use any other miniature wedge base bulbs including part numbers W5W, 194, 158, 2825 or a brighter LED unit.
Re-insert the socket in to the housing and rotate it 1/4 turn clockwise to secure it in place.
Replace White Connector
Replace Access Cover
Parking & Reverse Lights
The inner light housing on the trunk lid contains the reverse and parking light bulbs.
Open Trunk Lid
Loosen Plastic Phillips Screw
Pull Out Plastic Fasteners
Loosen the black plastic screws by turning them counter clockwise with a Phillips head screwdriver. Then pull out the entire black plastic fastener.
Pull Off Rubber Bumper
Pull Back Trunk Lid Liner
1/4 Turn Counter Clockwise
I removed four black plastic fasteners and two rubber bumpers.
Pull back the carpeted trunk lid liner and locate the parking light bulb socket.
Rotate the socket 1/4 turn counter clockwise and pull it straight out of the housing.
Pull Out Bulb Socket
Push Down & 1/4 Turn CC
Trunk Lid Liner Fasteners
Push a new # 1156 bulb down in to the socket and rotate it 1/4 turn clockwise to secure it in place.
Re-Insert Parking Light Socket
1/4 Turn Clockwise - Lock
Loosen 10mm Nuts
To access the reverse light bulb socket, you'll have to remove 3 nuts on the underside of the housing.
There are two nuts on the outer edge of the housing and one more near the inner edge.
Loosen the two outer nuts in the counter clockwise direction with a 10mm socket and ratcheting wrench.
3rd 10mm Nut
Loosen Counter Clockwise
3 10mm Nuts Removed
Set the three nuts aside in a safe place.
Pull Off Light Housing
Parking & Reverse Sockets
1/4 Turn Counter Clockwise
If you have trouble removing the housing, lightly tap on the screw ends with the handle of a screwdriver.
Rotate the small light gray reverse bulb socket 1/4 turn counter clockwise before pulling it straight out of the housing.
Pull Out Reverse Socket
Pull Out Old # 921 Bulb
1/4 Turn Clockwise - Lock
Re-insert the socket in to the housing and rotate it 1/4 turn clockwise to secure it in place.
Push On Light Housing
Tighten Outer 10mm Nuts
Tighten Clockwise - 3rd Nut
Carefully push the housing back in to place.
Spin on the 3 nuts in the clockwise direction a few turns by hand to prevent them from becoming cross threaded.
Tighten the three nuts by turning them clockwise with the 10mm socket and ratcheting wrench until they are snug.
Do not over tighten the nuts to avoid cracking the plastic housing.
Replace Trunk Lid Carpet
Push In Fasteners
Then push in the black plastic screws at the center of each fastener to secure them in place.
Push In Rubber Bumper
Test New Tail Light Bulbs
Test the new tail light bulbs by turning on the headlights, having someone step on the brake pedal, activate the hazard signals and place the transmission in reverse.
For more, check out my other Kia Optima Repair & Maintenance Guides.
Where Are Brake Light Located 2015 Kia Optima
Source: https://www.paulstravelpictures.com/Kia-Optima-Tail-Light-Bulbs-Replacement-Guide/
Post a Comment for "Where Are Brake Light Located 2015 Kia Optima"